( 5 : 1 ) a a b b c c d d e e f f a a b b c c d d 15-00066 o conec abc notes: 1. recommended solder instruction see sheet 2 2. ip rating: ip 67 3. sealed to withstand pressure up to 1,45 psi for 30 minutes after soldering 4. metalshell: zinc die cast; mi n. 50in nickel plating over copper 5. insulators: pbt gf ul 94 v-0, black 6. o-ring: silicone per astm d2000 70 shore a 7. rubber gasket: tpe 8. sealing compound: epoxy resin ul 94 v-0; black 9. contacts: copper alloy plating (see part no): o please add 1 for 30in hard gold over min. 50in nickel o please add 3 for 8in hard gold over min. 50in nickel solder cup accepts cable awg 22 10. hexlocking screws: stainless steel 11. recommended panel cut-out on sheet 2 12. recommended torque for mounting screw 35ncm (3.1 in.lb) / max.67ncm (6 in.lb) 13. connector is part marked: 15-00066 o conec abc b dim. in mm r date drawn inventor 10 t h i s d r a w i n g m a y n o t b e c o p i e d o r r e p r o d u c e d i n a n y w a y , a n d m a y n o t b e p a s s e d o n t o a t h i r d p a r t y w i t h o u t w r i t t e n p e r m i s s i o n . o w n e r s h i p a n d c o p y r i g h t o f c o n e c g m b h d-old norm appd. tolerance material: title: dwg no: din- sh: part no: name date name description rev. d o n o t a l t e r c a d d r a w i n g b y h a n d scale: customer approval date: name: title: company name: approval # freigabe # deblocage # autorizacion # approval a p p r o v a l # f r e i g a b e # d e b l o c a g e # a u t o r i z a c i o n approval # freigabe # deblocage # autorizacion approval # freigabe # deblocage # autorizacion # approval 15K1A272 a3 1 d-sub male hd see notes schmidt 11.09.08 15.09.08 fischer 26pos. solder cup with hexlocking screw 2:1 (5:1) 15-00066 aorigin 3 x b ? 3129 26.09.08 petker 3 x c ? 3435 01.10.09 hs b at all times water r esistant connectors not in use should be covered with a conec water resistant cap or water tight hood. c c c b o-ring 4-40 unc see note 13 o (see note 9) 2 1 , 1 - 0 0 , 3 + 25,14 - 0,02 0,23 + 33,32 - 0,12 0,13 + 47,7 - 0 0,3 + 4-40 unc sealing compound rubber gasket placed on top surface of male insulator 3 , 6 - 0 0 , 2 5 + 6 - 0 , 1 8 0 , 1 2 + 8,23 - 0 0,25 + 9 , 6 - 0 , 3 0 , 4 + 1 0 1 2 , 1 - 0 , 3 0 , 4 + 1,04 n (26x) 4 , 6 9 , 4 4,8 sw pos. 1 pos. 10 pos. 19
a a b b c c d d e e f f a a b b c c d d dim. in mm r date drawn inventor 10 t h i s d r a w i n g m a y n o t b e c o p i e d o r r e p r o d u c e d i n a n y w a y , a n d m a y n o t b e p a s s e d o n t o a t h i r d p a r t y w i t h o u t w r i t t e n p e r m i s s i o n . o w n e r s h i p a n d c o p y r i g h t o f c o n e c g m b h d-old norm appd. tolerance material: title: dwg no: din- sh: part no: name date name description rev. d o n o t a l t e r c a d d r a w i n g b y h a n d scale: customer approval date: name: title: company name: approval # freigabe # deblocage # autorizacion # approval a p p r o v a l # f r e i g a b e # d e b l o c a g e # a u t o r i z a c i o n approval # freigabe # deblocage # autorizacion approval # freigabe # deblocage # autorizacion # approval 15K1A272 a3 2 panel cut-out see sheet 1 schmidt 11.09.08 15.09.08 fischer d-sub male hd 26pos. solder cup with hexlocking screw 5:1 see sheet 1 aorigin 2 x b ? 3129 26.09.08 petker b b 3 , 4 r ` 0 , 1 3 1 1 , 4 ` 0 , 1 28,8 ` 0,1 3 , 1 ` 0 , 0 5 n ( 2 x ) i 0,26 b i 0,26 a 1 0 ` 1 33,32 ` 0,1 b a recommended panel cut-out solder instruction 1. cable should be prepared for solderin g. the cable/wires must be pretinned. 2. insert cable/wire into solder cup. 3. operate the soldering iron at 350c, 50 watt max. and use a pencil tip. 4. put tip to wire in solder cup. 5. after 1 second bring in solder. 6. heat for 3 seconds longer. do not heat contact more than 4 seconds in total. 7. remove soldering iron. 8. wait until solder gets rigid again. 9. do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up.
|
